Penghicorn | kitting up all the parts and panic shopping
2018-12-09 00:38:21
35C3 is in 17 days and I'm missing some parts - so I panic ordered some parts on LCSC.com, just to notice in checkout that for DHL express shipping they now want a VAT number. Hmm. Normal post it is then, let's hope all the stuff arrives before I leave to my grandparents place.
The only crucial parts missing are, apart from the hopefully soon arriving CC1101 and NRF modules: the CH340C and some neopixels. I should have added the crystal and caps pads for the CH340G just in case something like this would happen.. also I can't find my bag of neopixels.
Some parts I have to bodge on, for example some parts are 0805 and go on 0603 pads or vice-versa, but that should be fine.
Penghicorn | updates are on twitter
2018-11-24 21:59:49
hey, so currently f0wl is the only one able to work on the badge and there are some updates to find here https://twitter.com/thepenguicorn
that stupid thing everyone does differently | breadboarding first prototype
2018-10-24 14:14:05
To start with the first prototype I went with breakout boards for the chips, it's a bit botched, but fits. It was a bit tricky to find pin one on the TPS22917, but with the help of Alex I was able to decide on the right pin *hopefully*. On the left side is an HT7333 - I was thinking about using the AP2112K first, but the lower quiescent current of the HT7333 and general current consumption needs of the Attiny brought me to the holtek chip instead.
a "true" in system programmer | the pcb bug bit me - must be that part of the year
2018-10-17 00:42:19
I wanted to take a look at the firmware of my #BINCL - binary coded decimal 10mm LED clock to get rid of the pcbs I still have from the first batch. I quickly ran into the problem of having only 5V usbasp modules or my version one board with pogo pins, able to talk to 3v3 devices, but not power them. In this revision I've added a AP2112K and a second switch, changed the usb plug and made it a single side pcb. The edge connector is inverted from before and will now hold an ISP6 port instead of the pogo pins!
Boards aren't routed yet, price in a size like this on OSHpark for 3 boards is
MAX3421E FeatherWing | boards ordered
2018-10-16 10:17:37
I did something I haven't done before on this board, a matrix to reroute pins with solder jumpers. Otherwise the board looks fairly simple and boring, not much to route on it.
that stupid thing everyone does differently | notes from last discussion - just to keep them somewhere (not for public)
2018-10-14 17:16:18
gerade mal Fotos gemacht bevor ic hdie weggeschmissen habe:
Das kennst du glaube ich auch noch gar nicht, ist danach noch entstanden...ist aber nicht wirklich gut geworden:
that stupid thing everyone does differently | hardware decisions
2018-10-10 10:12:18
At first I thought I would slap an n-channel MOSFET to an attiny85, switch low-side (as in cut off the ground of PI) and call it a day. Then @Alex said high-side switching makes more sense, but complicates things. For a start you need a p-channel MOSFET instead AND to switch it off you need an extra transistor when your Attiny runs on 3.3V to achieve the voltage level that you're switching.
I learned a lot yesterday just by talking over whatsapp with Alex, while we were kind of distracted by the live stream of the "unexpected maker". In the end I found a chip called TPS22917, that Alex waved through as a "possible/passable candidate". This way I don't need a mosfet and a transistor etc.
square inch power muxer | social media stuff
2018-09-20 13:39:56
Here's a link to the instagram image, let's see how it performs :)
As usual I tried to make a video and some up a few things I've seen and liked - this time I was also running around with some other known-here people like @bitluni, @Alex , @Clemens Mayer and @Stefan Kremser
Stefan and I did a little swap of various gaming parts, I spontaneously joined a maker slam to present my #K.I.T.T. - KNIGHT RIDER badge/brooch and there were some other events to watch. The "Hannover Arduino Treffpunkt" is also featured with an improved version of my #RGB 16 Segment LED
A lot of fun on two days compressed in an 9 minute video with subtitles (which I will never ever do again, but probably should).
square inch power muxer | boards are ordered at oshpark
2018-09-09 15:42:39
I went over the design with a rested eye and everything looked good to go - hope it makes it in time to test, but I call it verified since it's working in my #LAMEBOY - another ESP12 handheld already anyway. I used super-swift but I was too cheap for upgrading the shipping :D
Also ordered them on aisler with a stencil, because why not?!
Game Boy Cartridge plus Programmer | small redesign of bivert module
2018-09-09 15:35:15
this design should finally allow me to put the PCB between the connector and cpu on a Game Boy pocket mainboard and solder it up with magnetic coil wire instead of the heavily isolated cables. I've ordered 12 2oz 0.8mm boards on OSHpark.
blinking things | boom, starblinken kit is on tindie!
2018-09-06 11:34:11
I've tested and verified my design and put it on tindie btw. :)
I'm nearly through my stock of Rev3 boards and close to another order. There was an issue with the LEDs glowing a bit when the battery was fresh. Two red LEDs in series on a fresh batterie just wasn't enough of a voltage drop. So I sat down and added 4 more 0805 resistors and rewired it completely. Now it should definitely not glow dimly in a "supposed to be off" state.
old version
new version
The SAO connector was moved to the bottom center, but I was too lazy to redo the OSHpark upload - png download cycle again.
WiFi and USB for pocketbeagle | getting started again for testing
2018-08-16 11:58:18
call this on a mac in your browser http://beaglebone.local/ - if you get the beagle page, it works! (connecting over usb that is)
ssh debian@beaglebone.local
with password temppwd (you should change that)
sudo iwlist wlan0 scan | grep ESSID
shows you stuff if
sudo iwconfig
shows you stuff if
lsusb
shows you stuff
zynthia - sequencer synthesizer | here's a little video
2018-08-05 19:50:59
working on that youtube channel makes me finish more projects, as it seems :)
blinking things | here's a little video
2018-07-29 16:23:27
zynthia - sequencer synthesizer | almost a year!
2018-07-25 01:15:45
Wow, it has been a while! I have the SMD boards assembled for a while now, but never came around testing them - I was just not interested in soldering all those resistors and LEDs again to get something that does almost exactly the same like the original does. Until yesterday, when I wired up a 90ies color schemed board :) check it out over here, I'll have a youtube video incoming soon, too.
resistor color code watch | some more binary clocks
2018-07-25 00:53:13
They kind of belong together, I've taken the neopixel 7 segment display from the "unexpected maker" tindie shop and adapted my code to show on his display.
And since it's a project of a youtuber and a binary clock, here's another video where I've build up the BCD crap clock by David Watts :)
blinking things | verified the board design
2018-07-22 16:34:59
I hand wired a combo of NE555, CD4017 and two ULN2003 chips. I also spray painted the protoboard before that. The capacitor I chose is a bit too small, so the animation is a bit too fast. I'll need to grab a 2uF instead of a 1uF cap. Definitely need to add a 100nF cap for the 555 and maybe some more all around.