LAMEBOY - another ESP12 handheld | slight redesign
2017-09-29 16:14:31
I always wanted to have a footprint that fit 0603 / 0805 / 1206 resistors or capacitors and for this project I finally started designing some. I'll need to test em properly, but this way everyone can use their parts with less hassle. Except for the resistor arrays, I won't change them.

http://www.resistorguide.com/resistor-sizes-and-packages/
PORG | Getting started with the pocketbeagle
2017-09-29 00:31:25
https://github.com/beagleboard/pocketbeagle/wiki/FAQ
https://github.com/beagleboard/pocketbeagle/wiki
https://beagleboard.org/pocket
https://octavosystems.com/2017/09/21/pocketbeagle-launch/
http://www.mouser.de/new/beagleboardorg/pocketbeagle/
Sadly 4 PWM pins aren't enough to get all 8-10 servos running, so I need a controller for that anyway, probably keep the arduino for that. Probably don't even need PWM for the servos though. (probably leeds to PCA9685 check #Servo Breakout for WeMos D1 Mini )
Totally neat: USB is on the GPIO headers. comparing that to the Raspberry PI derivates, that's pretty cool.
PORG | shopping in Murica
2017-09-27 21:34:03
I've bought a "target-only" plushy Porg with sound and also got one of the new https://beagleboard.org/pocket - at the Maker Faire New York. So I got the brains and maybe the skin and voice :)

I2C peripherals based on Attiny85 (mostly) | some attiny dev boards
2017-09-27 18:05:19
corrected the grove connector

also, for programming and prototyping:

LAMEBOY - another ESP12 handheld | RGB is finally working
2017-09-21 00:03:42
At the time of designing the boards it felt like a no brainer to use a BlinkM clone over I2C, because I had worked with them in my early beginnings. It took me a while though to finally burn the firmware and set the fuses right, but now I finally made it!
avrdude -c usbasp -p t45 -U lfuse:w:0xe2:m -U hfuse:w:0xdf:m
avrdude -c usbasp -p t45 -U flash:w:cyz_rgb_slave_attiny45.hex
I also found out that avrdude is able to slow down the clock frequency of SPI by itself. With -B 100 I was able to reprogram the tiny45, no matter how slow I was setting the fuses by accident.
My #a "true" in system programmer helped a lot burning the firmware onto the attiny!
Of course... of course. R and G are mixed up. gnargh. But here's a demo:
LAMEBOY - another ESP12 handheld | That is just the perfect color!
2017-09-20 13:50:34

LAMEBOY - another ESP12 handheld | case concept
2017-09-20 01:51:19
There's a little edge on the bottom left for the screw less corner. I want to preserve the colorful pcbs as much as i can but also protect the parts. I still need to add the "shoulder" buttons and roughly check if everything fits.

charlie-plexed icosahedron
2017-09-17 12:27:25

that's some tough stuff to get your head around, thanks to past dave I already had a cheat sheet :)


It get's worse from each iteration :D I was quite embarrassed when me and my mum pulled out the hotglue gun... looks a bit like Lukes Lightsaber training ball. I started a collection on thingiverse for inspiration of the next one https://www.thingiverse.com/deefdarko/collections/led-star
PORG | weird head mechanics
2017-09-17 00:20:43
I'm trying to replicate the head behaviour of the "my keepon", as seen here [https://hackaday.com/2009/10/29/keepon-eat-your-heart-out/] and so I try to 3D print something that might work. I can't make out if the servos are connected in a 90 or 180 degree angle, so I've added 4 screw holes. These are two parts, printed into each other with a distance of 0.5mm - let's hope that's enough room.
I googled it further and found out that I basically want a swashplate (that's my google term) - with that I'll get an awesome range for shoulders and head! Just imagine the head with some oled eyes and the shoulders attached to this part and I'm almost done. Well, not really. Not at all. The amount of servos used is 3, so like a delta bot basically. Not sure if the shaft has to be fixed or also on a ball joint.

zynthia - sequencer synthesizer | More Zynthias being build
LAMEBOY - another ESP12 handheld | quick fix for the regulator
2017-09-12 14:17:16
Since the AMS1117 regulator is not the best when it comes to the dropout voltage, I've made a little add on board, that will hopefully let me add the AP2112 regulator instead. They can be found on many adafruit boards, so I took that instead. I've ordered 12 boards, but the I'm still ashamed of what I "paid" and the board size :D

LAMEBOY - another ESP12 handheld | a *slightly* redesigned PCB
2017-09-12 08:38:36
Yesterday I've received my beautiful OSHPark boards and started to solder with the help of the stencil I got from OSHstencil.com. Sadly I've noticed that the crystal I got is the wrong size and I need to touch up some connections (pins are shorted at the power muxing chip etc.) I also need to solder the front side, meaning buttons and RGB LEDs.
Some thoughts about the parts used led me to change some footprints or completely swap parts. Already a lot of work to do again, but hopefully this way production might be easier and is not dependent on getting parts on ebay for cheap, but having them available on large amounts on digikey and mouser etc.
- To have almost every part available on mouser meant to switch the CH340G to the CP2102N, this also means no crystal footprint to worry anymore
- the LDO AMS1117 has not the lowest dropout voltage you can get for a board like this, so I switched to the AP2112 like adafruit uses on their huzza boards
- I've also changed the footprint of every cap and resistor to use 0603 parts
- There are still some footprints to change, like the SD card adapter
- probably the PCF8574 that scans then buttons (there are QFN and BGA footprints that are missing in my library)
- the I2C port / grove connector was 1.5mm by accident, so I also had to redesign that
- I've took out the complete RGB section with resistors, LEDs and transistors and replaced them with 2mm APA102 LEDs, will make rerouting a lot easier
- the footprint for the USB micro socket also doesn't have the holes, so I had to use the USB mini port
how to: Maker Faire | Demo Mode
2017-09-04 14:58:41
Laser cut faceplate, 3D printed case, two buttons and stereo 3.5mm plugs - for single and dual switching stuff :) this is definitely better than the cardboard box I had before! I'll add some demo functions and plugs to projects to show them off at the Zurich MakerFaire 2017 this weekend.

LAMEBOY - another ESP12 handheld | Assistive Technology Judges
2017-09-04 11:20:28
please ignore this, was too early for anything goes!
K.I.T.T. - KNIGHT RIDER badge/brooch | someone got lucky today
2017-09-01 16:35:57
So guess how many boards I got in my 10+ proto order at dirtypcbs? 40 pcbs! I have to stock up all the parts now :D

LAMEBOY - another ESP12 handheld | Hackaday API
2017-08-31 23:22:03
I've played around with the #Hackaday API to show me my likes. Yes, I'm one of those guys - I even noticed that it isn't the same like you can see on my profile page, since there the page likes are calculated in as well (bug is reported though).
At first I tried ArduinoJSON to extract the data, but then returned to char arrays and some brain-fu. Well some Strings are in as well, so it's not beautiful but get's results!
const char* skw = "skulls\":";
int counter = 0;
while (
client.available() &&
counter != 8
) {
char json = client.read();
if (json == skw[counter])
{
counter++;
}
else counter=0;
}
String skulls = client.readStringUntil(',');

LAMEBOY - another ESP12 handheld | game concept idea
2017-08-28 18:53:46
there's an invertDisplay function for the display, if you can find a version of the library that works on ESP8266 and you pipe in some lines of code... not the point now. The concept is inspired by stranger things, you have to get through a world and run into obstacles. You can only get through certain worlds by changing to the upside-down world (meaning invertDisplay) but there is that creature that closes in on you when you move, so you can't stay long on the other side.
video recap of #mfh17
2017-08-27 16:45:54
Maker Faire Hannover 2017 - fun times!
USB cable tester | yay :)
2017-08-26 07:59:34
so cool to see one in the wild!
LAMEBOY - another ESP12 handheld | Prototyped keyboard + display
2017-08-24 23:59:27
Thanks to @Radomir Dopieralski I've soldered up a semi prototype. LCD and keys work :) that makes everything on I2C and SPI pretty much work as well.
