Johnny IV | aftermath of Maker Faire Berlin 2017
2017-06-17 16:02:18
I've brought R8-J5, formally know as #R8-D8 - a distant relative of R2-D2 and #Johnny IV - I got a lot of questions like "what does it do?", first day the answer was "nothing", second day I've reactivated the eyes from the last log.
It needs a good power platform to start from, so I'll recycle some power bank batteries into a 2S cell. With the help of some cheap ebay modules and a switch.
WIFI Game Boy Cartridge | Starting with esp-idf-v2.0
2017-06-16 22:23:40
http://esp-idf.readthedocs.io/
Finally found the time and inspiration to work on this project again. To get the I2S demo of CNLohr working, I also needed to be able to compile with the esp-idf.
how to: Maker Faire | powering your projects
2017-06-16 11:29:18
@al1's battery box tip
LiPos have their special place in many of our projects, but sometimes it's just neat to have one of those AAA battery boxes with a switch that fits two-three batteries. Many of the common projects run just fine off them, like @al1 's #reCLOCK -> it's so tiny! But it also helps to show off the piece, because it makes it portable.
@Radomir Dopieralski's two cents
A. Make sure the batteries are easily removable, and take a few spares and a charger. This way you can charge one battery while the project runs on the other.
B. Remember that your projects are probably not designed to move all the time for 8+ hours straight. Motors get hot, servos wear out and break, batteries can only take so much recharging. So make breaks. If you have several projects, run one at a time. This will also encourage people to come back to your table later.
Use USB hubs and breadboards
Kind of obvious, but in case you want to power a lot of little projects, you can easily distribute power with a USB hub or use breadboards. Powered USB hubs should work pretty well, but you can also put HUBs on power banks!
BINCL - binary coded decimal 10mm LED clock | Deeeemooo
2017-06-03 16:37:48
The blue is still a bit too strong, even with a 1k resistor.. meh. (edit: progger runs on 5v, not the tested 3V3 :D )
BINCL - binary coded decimal 10mm LED clock | Binary sunset
2017-06-03 14:24:11
checking resistor values. Yellow gets 100 ohms, blue 1k ohms.

link drop for modding/repairing/hacking stuff | UNI-T UT61E
Heimdall - dumb remote home | TIL: echo dot has a speaker
2017-05-22 09:23:45
The echo dot currently runs for 55 Euros and I couldn't resist buying one! The option to chose your own speaker instead of paying 120 Euros more for the full echo was almost reason enough for me - but to my surprise I discovered that the echo dot also has an (admittedly crappy) speaker! It's enough to chat along and use IFTTT with adafruit.io+alexa receipts to switch the lights on by saying "echo trigger Küche ein" etc. - nice!
connection adafruit
address io.adafruit.com:1883
username ADAFRUIT_USERNAME
password ADAFRUIT_KEY
start_type automatic
cleansession false
notifications false
try_private false
topic inTopic in 0 "" davedarko/feeds/
It took me a while to figure out that the "remote_username" and "remote_password" on my raspberry had to be replaced by "username" and "password", since the mosquitto version on my PI is (still?) too old? [adafruit.io - bridge mqtt] To get some debug informations, stop the mosquitto service and start it as a program.
cd /etc/mosquitto/conf.d/
sudo systemctl stop mosquitto.service
mosquitto -c mosquitto.conf
WIFI Game Boy Cartridge | celebrations are in order
2017-05-14 23:37:21
http://hackaday.com/2017/05/14/hackaday-prize-entry-wifi-game-boy-cartridge/

I feel some questions are coming my way, so I've updated the detail section :)
blinking things | RGBY LEDs
2017-05-14 11:55:09
http://www.ebay.de/itm/172664995172
I've ordered some of CNLohr's RGBY LEDs for my WeMos shield, will update this once they arrive :)
Game Boy Cartridge plus Programmer | interesting puzzle game
2017-05-13 22:58:25
@Frank Buss just linked me this http://www.coolmath-games.com/0-bloxorz http://www.frank-buss.de/vectrex/index.html a neat little puzzle game. Should I ever come to writing a Game Boy game, then this would definitely be a candidate! Right after Game of Life of course.
WIFI Game Boy Cartridge | precognition in a game boy?
2017-05-13 14:24:35
So I thought to myself, if the ESP is too slow, but the query itself is taking microseconds instead of nanoseconds: why not trick the ESP and spit out the next in array? here's what I got, admittedly one of the better results, but you can finally read something! I can live with it, if I can get it to work reliably.

WIFI Game Boy Cartridge | i2s for parallel IN / OUT?
2017-05-13 01:14:28
https://www.esp32.com/viewtopic.php?f=19&t=1746&p=8153&hilit=parallel#p8153
Seems like I'm 3us late with reading and preparing my response. The posted scan looks like it takes 175us from address change to address change. Putting it in relation, an EEPROM takes 150ns to respond, that's 1/20 of the time I have now. With 240MHz the ESP32 should have a clock cycle time of 4.16ns. Whaaaat? My math is broken. Seems like the maximum speed for gpios on the ESP is "quite" limited, max toggle freq is around 4MHz. https://www.esp32.com/viewtopic.php?f=2&t=1595&p=7482&hilit=parallel#p7482
Seems like there is a multipin IS2 interface that was also used on https://github.com/igrr/esp32-cam-demo/blob/master/components/camera/camera.c#L314
https://www.esp32.com/viewtopic.php?f=12&t=951&p=4113&hilit=parallel#p4113
WIFI Game Boy Cartridge | moar research.
2017-05-12 20:48:51
So from far away it looks alright! I checked every byte and the data is correct. But...
Look a bit closer and you see this:

It might make sense to give the ESP the control over the OE of the data pins, since it's not fast enough to react to every change on the fly, it might needs better timing.
blinking things | HT16K33 board arrived
2017-05-11 21:09:29
Board works :)

BINCL - binary coded decimal 10mm LED clock | considerations for REV2
2017-05-09 10:26:29
As soon as I've had send the board, I just knew that new ideas would flood in. Here's a list of improvements for the board.
- bad pin planning: could have spared the RX/TX line and add an "FTDI" pinout, this way I need to program via ISP only
- add a transistor to the ground of the LEDs for dimming
- add a photo resistor for checking light of environment
BINCL - binary coded decimal 10mm LED clock | picture added
2017-05-09 10:21:40
I've added a size mockup with some 10mm LEDs I still have from other projects. The ones I've bought for this project look more like this:

WIFI Game Boy Cartridge | Needs moar research
2017-05-05 00:05:46
I can't believe that I'm so close already... but I do need to check the timings and need to find out if I can advance the code more. This needs to be connected to an analyzer.

WIFI Game Boy Cartridge | Hardware setup
2017-05-01 22:52:17
I'm still missing some cables, but so far it is looking quite interesting. I've recycled a donor board, replaced the missing switch with a wire, supply the game boy off of the 3V3 power of the esp board through a diode and soldered 32 cables to the missing cartridge port.

WIFI Game Boy Cartridge | what a week - no end in sight
2017-04-22 21:37:40
The whole week was filled with work - taking support calls, fixing bugs, meetings and more support calls. In between all that we tried to develop the important stuff. Yesterday, after work, I prepared my room for some dry wall construction ,to close the window between my room and the kitchen. Today I was mainly helping my father to build up the dry wall. The next few days I will be painting, letting it dry, glue on wallpaper, letting it dry, putting paint on the wallpaper and letting it dry as well. To make the Wohngemeinschaft great again. My bed is right next to the wall, before the wall I was awake when my roommate was.
I need to fix up the light switch as well - I see a Wemos D1 mini soon hanging there too :)
Anyways. Back to the project - I received all the parts to get prototyping started and I'm excited to begin, as soon as I can possibly do, but not today - I'm tired. Funding looks great, e-begging works :D
Game Boy Cartridge plus Programmer | Hackaday Prize 2017
2017-04-20 23:24:22
#WIFI Game Boy Cartridge - this is my entry for the hackaday.io prize. It is all based on the efforts I've made in this project. But everything I've done here was also in preparation for having an Internet connected Game Boy. Once the IoT segment of the prize is opened, I will submit the project to that as well.
There is currently a funding round, where every like get's you a dollar - you probably have already heard about that ;) It would be great if you could head over there and add a like to the project - feel free to remove the like once the funding is over and maybe give it back once everything works :D that would be pretty motivational.
Anyway, I wish all the contestants the best of luck!